A Comprehensive Guide to PP Injection Molding

Polypropylene, commonly known as PP, is renowned for its excellent resistance to bending fatigue, earning it the nickname "Hinge Plastic" or "Bǎi zhé jiāo" in Chinese. PP is a semi-transparent, semi-crystalline thermoplastic that boasts high strength, excellent electrical insulation, low moisture absorption, a high heat deflection temperature, low density, and high crystallinity.

To enhance its properties for specific applications, PP is often modified with fillers such as glass fiber, mineral fillers, or thermoplastic rubber. The flow rate of PP varies significantly depending on its grade, but generally, its fluidity falls between that of ABS and PC.

Here is a detailed breakdown of the injection molding process for Polypropylene[^1].

1. Material Preparation and Handling

Pure PP is a semi-transparent ivory white granule that can be colored in various shades.

• Coloring: On standard injection molding machines, PP is typically colored using masterbatches (color concentrate). However, machines with independent plasticizing elements that enhance mixing (like certain Hongmeida models) can also use color powder.
• Recycling: The proportion of recycled material should not exceed 15%. Exceeding this limit can lead to decreased strength, degradation, and color variation.
• Drying: Generally, PP does not require special drying treatment before Spritzgießen[^2], provided it is stored properly.

> ? Pro Tip: For outdoor applications, ensure the PP compound includes UV stabilizers and carbon black to prevent degradation from sunlight.

2. Injection Molding Machine Selection

There are no special requirements for the injection molding machine itself. However, due to the high crystallinity of PP, it is advisable to use a computer-controlled machine capable of high injection pressures and multi-stage control.

• Clamping Force: Generally calculated at 3800 t/m².
• Shot Volume: The injection volume should ideally be between 20% and 85% of the machine's capacity.


3. Mold and Gate Design

Mold design is critical for PP due to its shrinkage characteristics.

• Mold Temperature: Typically 50–90°C. Use higher mold temperatures for parts with strict dimensional requirements. The core temperature should be at least 5°C lower than the cavity temperature.
• Runners: Sprue diameter should be 4–7mm.
• Gates:
  • Pin gates: Length 1–1.5mm, diameter can be as small as 0.7mm.
  • Edge gates: Keep length short (approx. 0.7mm), depth at half the wall thickness, and width at twice the wall thickness.
• Venting: The mold must have excellent venting. Venting slots should be 0.025mm–0.038mm deep and 1.5mm thick.
• Avoiding Sink Marks: Use large, round sprues and circular runners. Ribs should be thin (approx. 50–60% of the wall thickness).
• Wall Thickness: Products made from homopolymer PP should not exceed 3 mm in thickness to avoid air traps; copolymer PP is required for thicker walls.

4. Processing Parameters Table

To help you visualize the optimal settings, here is a summary of the key processing parameters:

5. Melt Temperature Details

While the melting point of PP is between 160°C and 175°C, and its decomposition temperature is around 350°C, the processing temperature should never exceed 275°C. The optimal Schmelztemperatur[^3] for the melt section is around 240°C.

6. Injection Speed

To minimize internal stress and warpage, high-speed injection is generally recommended. However, for certain grades of PP or specific mold designs, high speed may cause air traps or flow marks.

• Textured Surfaces: If you notice light/dark streaks radiating from the gate on a textured surface, switch to low-speed injection combined with a higher mold temperature.

7. Injection and Holding Pressure

PP requires relatively high injection pressure (1500–1800 bar). The holding pressure[^4] should be approximately 80% of the injection pressure.

• Switch-over Point: Switch to holding pressure at roughly 95% of the full stroke.
• Duration: Use a longer holding time to ensure proper packing and reduce shrinkage.

8. Post-Processing

To prevent dimensional changes caused by post-crystallization shrinkage, finished products often require a post-treatment process, such as soaking in hot water.

[^1]: Explore the diverse applications and unique properties of Polypropylene, a versatile thermoplastic. [^2]: Learn about the injection molding process, a key technique in manufacturing plastic products. [^3]: Learn why melt temperature is crucial in the injection molding process and how it affects product quality. [^4]: Explore the role of holding pressure in injection molding and its impact on product integrity.

Über den Autor

Alex Yu

Ideal Pro Manufacturing

Alex ist Mitbegründer von Ideal Pro, doch wenn er nicht gerade wichtige Projekte beaufsichtigt oder das technische Team leitet, trifft man ihn wahrscheinlich auf einer langen Radtour, auf der Suche nach dem besten Kaffee der Stadt oder bei der Planung seines nächsten Reiseabenteuers. Mit über 20 Jahren Erfahrung in den Bereichen internationaler Vertrieb und Projektmanagement hat er schon alles gesehen – enge Fristen, knifflige technische Probleme und alles, was dazwischen liegt. Er ist davon überzeugt, dass großartige Arbeit von einem ausgeruhten Geist und einer guten Tasse Kaffee entsteht, und er bringt dieselbe Neugier und Liebe zum Detail in jedes Projekt ein, das er übernimmt. Wenn er nicht im Büro ist, befindet er sich meist irgendwo im Freien, erkundet neue Orte und sammelt Geschichten, die er gerne weitergibt.