시제품부터 양산까지 맞춤형 플라스틱 부품 — 지금 바로 견적을 받아보세요. WhatsApp +86 156 0682 1288 [email protected]
사출 성형

Key Plastic Properties for Injection Molding: Flow, Moisture & Shrinkage

Alex Yu

Alex Yu

읽는 데 5분

게시일: May 28 2026

Key Plastic Properties for Injection Molding: Flow, Moisture & Shrinkage

Key Plastic Properties Every Injection Molder Must Know

Successful 사출 성형 isn't just about the machine settings; it starts with a deep understanding of the material itself. Before setting process parameters or troubleshooting defects, every molding professional must thoroughly understand the physical and chemical properties of the plastic being used.

In this article, we will explore the four major plastic properties that directly impact your production quality: Flowability, Moisture Content, Shrinkage Rate, and Processing Temperature.


Flowability (Melt Flow)

What is Flowability? Flowability refers to the ability of molten plastic to fill the entire mold cavity under heat and pressure. It is typically measured using specialized fluidity testing molds.

Different grades of the same plastic family can have vastly different flow rates. Furthermore, the complexity of your part design dictates the required flowability.

Finding the Right Balance Selecting the correct flowability is a balancing act based on product structure, size, and wall thickness:

  • 너무 높음: If the plastic flows too easily, the melt may not pack tightly, leading to loose structures and poor product quality. Excessive flow often causes flash (burrs), mold sticking, and nozzle drool (drooling), which can clog the sprue.
  • 너무 낮음: For complex parts with long flow paths, low flowability makes filling difficult. This often results in short shots (incomplete filling) and sink marks, generating significant scrap. It may also require excessively high injection pressure, leading to high internal stress in the part.

Plastic melt flowability test mold and injection molding defects comparison.


Moisture Absorption and Volatile Content

Thermoplastics naturally contain some level of moisture and volatiles. Interestingly, a very small amount of moisture can actually act as a plasticizer. However, exceeding the allowable limit leads to serious processing issues.

The Dangers of Excess Moisture If moisture and volatiles are too high, you will encounter problems such as:

  • Material degradation and fogging.
  • Reduced mechanical strength.
  • Silver streaks (splay) and bubbles.
  • Rough surface finish.
  • Loss of transparency in clear parts (cloudiness).

Is "The Drier the Better"? No. This is a common misconception. Absolutely dry plastic can suffer from reduced flowability and increased brittleness, making mold filling difficult. The goal is to reach the optimal moisture level, not zero.

Main Causes of High Moisture/Volatiles: A. Low average molecular weight of the resin. B. Insufficient drying during the resin manufacturing process. C. Improper storage of hygroscopic plastics, causing them to absorb moisture from the air.

Note: Different plastics require specific drying temperatures and durations.

Silver streaks defect caused by moisture in injection molding.

The table below outlines the specific drying requirements for various plastic materials to ensure optimal processing.

Plastic NamePermissible Moisture (%)건조 온도 (°C)
폴리에틸렌(PE)0.0171
폴리스티렌 (PS)0.05 ~ 0.1071 ~ 79
Cellulose PlasticsMax 0.4065 ~ 87
Polyvinyl Chloride (PVC)0.0860 ~ 93
PolyesterMax 0.02121
폴리프로필렌(PP)0.1071 ~ 82
Acetate Fiber Plastics0.1076 ~ 87
나일론 (PA)0.04 ~ 0.0871

수축률

Shrinkage is inevitable in injection molding. Understanding why it happens is key to maintaining tight tolerances.

Why Does Plastic Shrink? A. Thermal Contraction: Plastics have a much higher thermal contraction rate than metals (roughly an order of magnitude larger, about 10x). B. Elastic Recovery: After hardening, the part is not a perfect rigid body and exhibits some elastic recovery upon ejection. C. Plastic Deformation: When the mold opens, pressure drops, but the part may still stick to the mold wall, undergoing slight plastic deformation.

Crystalline vs. Amorphous Factors influencing shrinkage include material properties, molding conditions, and part/mold design.

  • Amorphous Plastics: Shrinkage is typically less than 1%.
  • Crystalline Plastics: Shrinkage usually exceeds 1%. These materials exhibit "post-shrinkage," meaning dimensions continue to change after ejection. Accurate measurement should be taken 24 hours after cooling, achieving precision up to 0.02mm.

Comparison of shrinkage rates between crystalline and amorphous plastics.

Molding Shrinkage Rates by Polymer Type

Understanding shrinkage is critical for mold design and dimensional accuracy. Note the difference between amorphous and crystalline plastics, as well as the effect of glass fiber reinforcement.

카테고리Plastic NameNon-Reinforced Shrinkage (%)Glass Fiber Reinforced Shrinkage (%)
Amorphous Plastics폴리스티렌 (PS)0.3 ~ 0.6—
Styrene-Butadiene Copolymer (SB)0.4 ~ 0.7—
SAN Resin0.4 ~ 0.70.1 ~ 0.3
ABS Resin0.4 ~ 0.70.2 ~ 0.4
PMMA (아크릴)0.3 ~ 0.7—
폴리카보네이트(PC)0.6 ~ 0.80.2 ~ 0.5
Rigid PVC0.4 ~ 0.7—
Modified PPO0.5 ~ 0.90.2 ~ 0.4
Polysulfone (PSU)0.6 ~ 0.80.2 ~ 0.5
Cellulose Plastics0.4 ~ 0.7—
Crystalline Plastics폴리에틸렌(PE)1.2 ~ 3.8—
폴리프로필렌(PP)1.2 ~ 2.50.5 ~ 1.2
폴리옥시메틸렌(POM)1.8 ~ 3.00.2 ~ 0.8
Polyamide 6 (Nylon 6)0.5 ~ 2.20.7 ~ 1.2
Polyamide 66 (Nylon 66)0.5 ~ 2.5—
Polyamide 610 (Nylon 610)0.5 ~ 2.5—
Polyamide 11 (Nylon 11)1.8 ~ 2.5—
PET Resin1.2 ~ 2.00.3 ~ 0.6
PBT Resin1.4 ~ 2.7—

4. Processing Temperature

The processing temperature is the range where the plastic reaches its viscous flow state. It is not a single point, but a window between the Melting Point and the Decomposition Temperature.

When selecting the processing temperature, you must consider:

  • Part size, complexity, and wall thickness.
  • Presence of inserts.
  • Heat resistance of colorants/additives.
  • Machine capabilities.

Why Do Temperature Settings Vary? You might notice that the temperature displayed on the controller often differs from the actual melt temperature, or that the same mold requires different settings on different machines.

This is because the temperature shown on the control panel is an indirect, localized reading from a sensor, not the exact temperature of the molten plastic inside the barrel. Variations in sensor placement, thermocouple performance, and heating band efficiency all contribute to these differences. Therefore, process settings often need fine-tuning based on the specific machine and actual melt condition.

Injection molding machine barrel temperature control panel and melting range.


Checklist: What to Know Before You Mold

To scientifically set process conditions and troubleshoot effectively, every injection molder should review the following data sheet properties before starting production:

  • Type & Grade: Understand the chemical composition.
  • Density: Crucial for setting multi-stage injection positions.
  • Hygroscopicity & Allowable Moisture: Determines drying time and temperature.
  • Glass Transition (Tg), Melting Point (Tm), & Decomposition Temp: Sets the barrel temperature profile.
  • Melt Flow Index (MFI/MFR): Guides injection pressure and back pressure settings.
  • 결정도: Affects mold and melt temperature choices.
  • Allowable Injection Pressure Range: Ensures machine capability matches material needs.
  • Residence Time: How long the plastic can stay in the barrel before degrading (important for shot size and shutdown procedures).
  • Molding Shrinkage Rate: Essential for mold design and dimension control.
  • Mold Temperature Range: Critical for surface finish and cycle time.
  • Other Properties: Chemical resistance and Heat Deflection Temperature (HDT) for post-processing considerations.

? 给你的额外排版与SEO建议:

  1. 内部链接 (Internal Linking): 如果你之前发布了那篇《TPR/TPE热塑性弹性体的注塑成型》的文章,请务必在文中提到“不同牌号的塑料”或“吸湿性塑料”时,链接回那篇文章。这能形成良好的网站内链结构。
  2. 表格化数据: 在第4部分的Checklist中,如果可能的话,用WordPress的表格块(Table Block)来展示这些属性,会比纯文本列表看起来更专业,也更容易被Google抓取为精选摘要(Featured Snippet)。
  3. 强调重点: 我在译文中使用了加粗(Bold)来突出关键术语(如 Flash, Short shots, Crystalline),这有助于读者快速扫描文章,也能向搜索引擎强调页面的核心主题。

저자 소개

Alex Yu

Alex Yu

아이디얼 프로 매뉴팩처링

알렉스는 Ideal Pro의 공동 창립자이지만, 주요 프로젝트를 총괄하거나 기술 팀을 이끌지 않을 때는 장거리 자전거 타기를 즐기거나, 동네에서 가장 맛있는 커피를 찾아다니거나, 다음 여행 계획을 세우는 모습을 볼 수 있습니다. 국제 무역 영업과 프로젝트 관리 분야에서 20년 이상의 경력을 쌓아온 그는 촉박한 마감 기한부터 까다로운 엔지니어링 문제까지, 그 사이의 모든 상황을 다 겪어보았습니다. 그는 훌륭한 성과는 충분한 휴식을 취한 마음과 맛있는 커피에서 나온다고 믿으며, 맡은 모든 프로젝트에 그와 같은 호기심과 세심한 주의를 기울입니다. 사무실에 있지 않을 때는 대개 야외 어딘가에서 새로운 장소를 탐험하며, 나중에 나눌 이야기를 수집하곤 합니다.