주요 특성
- 수축
- 0.8-1.2 %
- 녹다
- 180-10 °C
- 곰팡이
- 30-0 °C
- 밀도
- 1.10-.25 g/cm³
- HDT
- 70-00 °C
- 건조
- 3- h at 80 °C
등급 선정 시 일반적으로 적용되는 기준값입니다. 금형이나 공차를 확정하기 전에 수지 공급업체의 기술 데이터 시트(TDS)를 참조하여 정확한 등급을 확인하십시오.
나란히
What TPU actually is
TPU is a flexible engineering elastomer used for gaskets, soft-touch overmoulds and wear-resistant components. Can be either ester-based (better oil resistance) or ether-based (better hydrolysis resistance). The tool runs cooler than hard engineering plastics.
Chemically, TPU belongs to the Thermoplastic polyurethane - engineering family. The polymer chain structure — linear and semi-crystalline — is what sets its shrinkage behaviour, temperature ceiling and melt flow. Like every thermoplastic, its properties are the result of processing history as much as of the resin grade itself: slow cooling increases crystallinity and brittleness, fast cooling locks in an amorphous structure and a different shrink. Resin suppliers offer TPU in commodity, reinforced and specialty grades, and the first selection step is to pick the right family before settling on a specific TDS.
처리 창
일반적인 공정 범위는 용융 온도가 약 180-10 °C 그리고 금형 온도는 약 30-0 °C. 그 범위 내에서는 수지가 예측 가능한 방식으로 채워지고, 압축되며, 배출됩니다. 그 범위 밖에서는 고장 양상이 모호하기보다는 구체적으로 나타납니다.
Above the recommended melt temperature, TPU can degrade thermally — the symptom is silver streaking, a mottled surface and a measurable loss of impact strength that the part carries into service. Long residence time in a large barrel running small shots is as damaging as a direct temperature overshoot, because the resin sits at temperature longer than intended. Below the lower bound, the melt freezes before it has fully packed the cavity: the part shows visible weld lines, flow marks around the gate and a surface that reads differently across the flow path.
Drying is 3- h at 80 °c. TPU absorbs moisture readily from ambient air, and moulding it wet produces silver streaks that look like overheat and cannot be fixed by lowering the barrel temperature. 3- h at 80 °C is the normal starting window. The resin supplier TDS always takes precedence over a generic figure on drying and moisture content.
수축 및 치수 공차
이 도구를 다음과 같이 설계하십시오. 0.8-1.2 % 수축을 고려하여, 실제 수치가 그 범위 내의 중간 지점이 아닌 특정 지점에 위치할 것으로 예상합니다. 이 값은 벽 두께, 유동 길이, 게이트 위치, 충진 압력, 유지 시간 및 금형 온도에 의해 결정됩니다. 두꺼운 부분은 수축해야 할 용융물이 더 많기 때문에 수축이 더 크게 발생하며, 유동 경로가 길면 캐비티가 완전히 채워지기 전에 압력이 떨어지기 때문에 게이트 쪽 끝보다 먼 쪽 끝에서 수축이 더 크게 나타납니다.
TPU is semi-crystalline, which means shrinkage is directional — flow-direction shrinkage differs from cross-flow shrinkage. That is why a single global shrink factor is a starting point, not an answer. On a long, thin part, the difference between the gate end and the far end can exceed the tolerance you are trying to hold. The fix is either to gate where the pressure can reach the whole part, to add a packing profile, or to accept that the tight tolerance belongs on the features near the gate and not on the overall length.
우리는 공차 상한치 범위 내에서 첫 번째 시편을 절단하고, 금형에 가공을 시작하기 전에 CMM을 사용하여 첫 번째 가공품을 측정합니다. 측정된 부품 데이터를 바탕으로 공구를 보정하는 것이 데이터 시트에 명시된 범위만을 기준으로 보정하는 것보다 비용이 적게 들고 신뢰성도 높으며, 이 측정 기록은 동일한 등급의 다음 공구를 제작할 때의 기준이 됩니다.
What TPU asks of the mould steel
The default steel family for TPU is P20 / 718H. 이러한 선택은 마모성, 금형 온도, 화학적 부식 위험이라는 세 가지 특성이 복합적으로 작용하여 결정됩니다.
연마성은 낮음. 이 수지에는 연마성 충전재가 포함되어 있지 않으므로, 게이트, 러너 및 벤트 부위가 용융물에 의해 침식되지 않으며, 일반적으로 사전 경화 처리된 블록만으로도 충분합니다. 향후 충전재가 포함된 등급으로 전환될 가능성이 있는 금형의 경우, 교체 가능한 게이트 인서트를 사용하는 것이 여전히 권장되는 방법입니다.
Mould temperature matters. TPU wants a mould at 30-0 °C, and a tool designed for a different temperature will run unevenly when set to it. Cooling channels need to be placed where the heat actually concentrates — at thick bosses, at the gate, and where the part joins the runner system — not spread evenly around the cavity. A tool that cools the thin walls and the thick boss at the same rate will hold a flat part and still show a sink mark on the boss.
Applications where TPU wins
TPU wins on strength-to-weight ratio and heat resistance. It is chosen where the part needs stiffness and impact resistance above what commodity grades deliver. Common application families include automotive interior and exterior components, appliance and consumer housings, electrical connectors, industrial structural parts and medical device components.
Where TPU gets replaced is usually clear. When the part has to survive aggressive solvents or continuous UV exposure, a different family takes over. When the temperature ceiling of TPU is exceeded, a high-temperature polymer steps in. When the resin itself is corrosive — PVC or a flame-retardant grade — the tool steel changes before the resin does.
디자인 지침
- 벽 두께. 대부분의 등급에서 명목 벽 두께를 1.5~3.0 mm 범위로 유지하십시오. 벽이 두꺼우면 침하 및 수축이 발생하기 쉬우며, 얇으면 충진이 불완전해질 위험이 있습니다. 두꺼운 부분에서 얇은 부분으로 급격하게 변하는 단차를 피하십시오.
- 갈비. 인접한 벽 두께의 약 0.5~0.6배 정도 두께로 리브를 형성하면 리브가 표면을 가라앉히는 것을 방지할 수 있습니다. 리브 사이의 틈새로 냉각 및 환기가 이루어질 수 있도록 리브 간격을 적절히 조정하십시오.
- 초안. 매끄러운 벽면에서는 최소 1°, 질감이 있는 벽면에서는 1.5–2°로 설정하십시오. 홈이 깊은 곳에는 각도를 더 크게 주십시오. 질감이 가장 깊은 곳에서 부품이 가장 많이 끌립니다.
- 필레. 내부 모서리에 벽 두께의 0.5배 이상인 필렛을 형성하면, 충격이 균열로 이어지는 응력 집중을 방지할 수 있습니다.
- 상사들. 정격 두께의 약 0.6배 정도 되는 두께의 벽을 사용하고, 보스를 두껍게 만드는 대신 거셋을 추가하며, 보스의 높이는 직경의 약 2.5배 미만으로 유지하십시오.
비용 및 사이클 타임에 미치는 영향
TPU sits in the middle of engineering thermoplastics on price; the premium over commodity grades buys temperature and stiffness, not a long cycle. The cost triangle is material price, cycle time and yield. A cycle that is a few seconds shorter on a high-volume part is worth more than the material saving, because the press hour is the dominant cost.
수율은 저렴한 수지가 오히려 비용이 많이 들게 되는 부분입니다. 수지가 습한 상태에서는 은색 줄무늬가 생기거나 불량품이 발생하고, 금형이 차가우면 현장 사용 중 파손되는 약한 용접선이 생기며, 탈기가 제대로 되지 않은 금형에서는 재가공이 필요한 탄 자국이 생깁니다. 이 모든 것은 재료비가 아니며, 저급 재료를 구매해 절약하는 몇 퍼센트의 비용보다 훨씬 더 큰 비용을 초래합니다.
흔히 저지르는 선발 실수
- 측정 루프 없이 전역 수축 계수를 사용하는 경우. 명목상 허용치는 출발점일 뿐, 정답은 아닙니다. 첫 측정 샷부터 정확하게 측정하십시오.
- Specifying TPU outside its temperature ceiling. 정격 HDT를 초과하는 사용 온도에서는, 비록 시제품 검사에 합격했다 하더라도 부품의 수명 기간 동안 그 거동 특성이 달라집니다.
- 수지 주입 시 마모 현상을 간과하는 경우. 유리 섬유가 함유된 성형품에서 사전 경화된 블록은 전체적인 마모가 나타나기 훨씬 전에 게이트 부분에서 마모가 발생합니다.
- 건조 및 수분 함량에 관한 수지 TDS를 확인하지 않았습니다. 흡습성 등급의 경우 건조 과정은 필수이며, 이 과정을 생략하면 성형 문제로 보이는 표면 결함이 나타납니다.
